您好,欢迎来到同达科技(大连)有限公司官网!

业务热线: 136 1084 5997

座机:0411-87553295-888

关键词:冲压模具,冲压剪板,冲压加工件,模具制造,模具供应,模具零部件加工,模具配件,汽车零部件模具,大连开发区冲压,冲压件

您现在的位置是:同达首页 > 资讯列表 > 行业新闻

行业新闻

模具行业相关中英文词组对照表

本文章发表于: 作者:Jessie 时间:2016-04-04 点击: 1753
 
一、进入位:gate location
水口形式:gate type
大水口:edge gate
细水口:pin-point gate
水口大小:gate size
转水口: switching runner/gate
唧嘴口径:sprue diameter
二、流道:runner
热流道:hot runner,hot manifold
热嘴冷流道:hot sprue/cold runner
唧嘴直流:direct sprue gate
圆形流道:round(full/half runner
流道电脑分析:mold flow analysis
流道平衡:runner balance
热嘴:hot sprue
热流道板:hot manifold
发热管:cartridge heater
探针:thermocouples
插头:connector plug
插座:connector socket
密封/封料:seal
三、运水:water line
喉塞:line lpug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socker
四、模具零件:mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
托板: support plate
螺丝:screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针: ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架):mold base
上内模:cavity insert
下内模:core insert
行位(滑块):slide
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate
撑头:support pillar
唧嘴:sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock set
推杆:push bar
栓打螺丝:S.H.S.B
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子弹弓:ball catch
喉塞:pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
术语:terms
承压平面平衡:parting surface support balance
模排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side
模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件:Do not use (core/cavity) insert
用铍铜做镶件:use beryllium copper insert
初步(正式)模图设计:preliinary (final) mold design
反呵:reverse core
弹弓压缩量:spring compressed length
稳定性好:good stability,stable
强度不够:insufficient rigidity
均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode


dowel pin定位梢
draft拔模锥度
draw bead张力调整杆
drive bearing传动轴承
ejection pad顶出衬垫
ejector脱模器
ejector guide pin顶出导梢
ejector leader busher顶出导梢衬套
ejector pad顶出垫
ejector pin顶出梢
ejector plate顶出板
ejector rod顶出杆
ejector sleeve顶出衬套
ejector valve顶出阀
eye bolt环首螺栓
filling core椿入蕊
film gate薄膜形浇口
finger pin指形梢
finish machined plate角形模板
finish machined round plate圆形模板
fixed bolster plate固定侧模板
flanged pin带凸缘销
flash gate毛边形浇口
flask上箱
floating punch浮动冲头
gate浇口
gate land浇口面
gib凹形拉紧楔
goose neck鹅颈管
guide bushing引导衬套
guide pin导梢
guide post引导柱
guide plate导板
guide rail导轨
head punch顶头冲孔
headless punch直柄冲头
heavily tapered solid整体模蕊盒
hose nippler管接头
impact damper缓冲器
injection ram压射柱塞
inlay busher嵌入衬套
inner plunger内柱塞
inner punch内冲头
insert嵌件
insert pin嵌件梢
king pin转向梢
king pin bush主梢
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子
shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆
spring-box eject-plate弹簧箱顶板
bushing block衬套
insert入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
scraped products报放心品
defective products不良品
finished products成品
disposed products处理品
barcode条形码
flow chart流程窗体
assembly组装
stamping冲压
molding成型
spare parts=buffer备品
coordinate坐标
dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band加热片
thermocouple热电偶
sand blasting喷沙
grit砂砾
derusting machine除锈机
degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应
ram连杆
edge finder巡边器
concave
convex
short射料不足
nick缺口
speck瑕疪
shine亮班
splay银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金
magnesium镁金
metal plate钣金
lathe
mill
plane
grind
drill
boring
blinster气泡
fillet镶;嵌边
through-hole form通孔形式
voller pin formality滚针形式
cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状
torque扭矩
spline=the multiple keys花键
quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的
moly high speed steel钼高速的
organic solvent有机溶剂
bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图
procedure dwg工程图
die structure dwg模具结构图
material材质
material thickness料片厚度
factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉
dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒
pin
lifter guide pin浮升导料销
guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套


模板类
top plate上托板(顶板)
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
deburring punch压毛边冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
101个热处理常用英文词汇
1. indication缺陷
2. test specimen试样
3. bar棒材
4. stock原料
5. billet方钢,钢方坯
6. bloom钢坯,钢锭
7. section型材
8. steel ingot钢锭
9. blank 坯料,半成品
10. cast steel铸钢
11. nodular cast iron球墨铸铁
12. ductile cast iron球墨铸铁
13. bronze青铜
14. brass黄铜
15. copper合金
16. stainless steel不锈钢
17. decarburization脱碳
18. scale氧化皮
19. anneal退火
20. process anneal进行退火
21. quenching淬火
22. normalizing正火
23. Charpy impact text夏比冲击试验
24. fatigue疲劳
25. tensile testing拉伸试验
26. solution固溶处理
27. aging时效处理
28. Vickers hardness维氏硬度
29. Rockwell hardness洛氏硬度
30. Brinell hardness布氏硬度
31. hardness tester硬度计
32. descale除污,除氧化皮等
33. ferrite铁素体
34. austenite奥氏体
35. martensite马氏体
36. cementite渗碳体
37. iron carbide渗碳体
38. solid solution固溶体
39. sorbite索氏体
40. bainite贝氏体
41. pearlite珠光体
42. nodular fine pearlite/ troostite屈氏体
43. black oxide coating发黑
44. grain晶粒
45. chromium
46. cadmium
47. tungsten
48. molybdenum
49. manganese
50. vanadium
51. molybdenum
52. silicon
53. sulfer/sulphur
54. phosphor/ phosphorus
55. nitrided氮化的
56. case hardening表面硬化,表面淬硬
57. air cooling空冷
58. furnace cooling炉冷
59. oil cooling油冷
60. electrocladding /plating电镀
61. brittleness脆性
62. strength强度
63. rigidity刚性,刚度
64. creep蠕变
65. deflection挠度
66. elongation延伸率
67. yield strength屈服强度
68. elastoplasticity弹塑性
69. metallographic structure金相组织
70. metallographic test金相试验
71. carbon content含碳量
72. induction hardening感应淬火
73. impedance matching感应淬火
74. hardening and tempering调质
75. crack裂纹
76. shrinkage缩孔,疏松
77. forging锻(件)
78. casting铸(件)
79. rolling轧(件)
80. drawing拉(件)
81. shot blasting喷丸(处理)
82. grit blasting喷钢砂(处理)
83. sand blasting喷砂(处理)
84. carburizing渗碳
85. nitriding渗氮
86. ageing/aging时效
87. grain size晶粒度
88. pore气孔
89. sonim夹砂
90. cinder inclusion夹渣
91. lattice晶格
92. abrasion/abrasive/rub/wear/wearing resistance (property)耐磨性
93. spectrum analysis光谱分析
94. heat/thermal treatment热处理
95. inclusion夹杂物
96. segregation偏析
97. picking酸洗,酸浸
98. residual stress残余应力
99. remaining stress残余应力
100. relaxation of residual stress消除残余应力
101. stress relief应力释放
机械类常用英语:冲压模具-零件类
punch冲头
insert入块(嵌入件)
groove punch压线冲子
round punch圆冲子
roller滚轴
baffle plate挡块
located block定位块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
landed plunger mold有肩柱塞式模具
burnishing die挤光模
landed positive mold有肩全压式模具
button die镶入式圆形凹模
loading shoe mold料套式模具
center-gated mold中心浇口式模具
loose detail mold活零件模具
chill mold冷硬用铸模
loose mold活动式模具
clod hobbing冷挤压制模
louvering die百叶窗冲切模
composite dies复合模具
manifold die分歧管模具
counter punch反凸模
modular mold组合式模具
double stack mold双层模具
multi-cavity mold多模穴模具
electroformed mold电铸成形模
multi-gate mold复式浇口模具
expander die扩径模
offswt bending die双折冷弯模具
extrusion die挤出模
palletizing die叠层模
family mold反套制品模具
plaster mold石膏模
blank through dies漏件式落料模
porous mold通气性模具
duplicated cavity plate复板模
positive mold全压式模具
fantail die扇尾形模具
pressure die压紧模
fishtail die鱼尾形模具
profile die轮廓模
flash mold溢料式模具
progressive die顺序模
gypsum mold石膏铸模
protable mold手提式模具
hot-runner mold热流道模具
prototype mold雏形试验模具
ingot mold钢锭模
punching die落料模
lancing die切口模
aising(embossing)压花起伏成形
re-entrant mold倒角式模具
sectional die拼合模
runless injection mold无流道冷料模具
sectional die对合模具
segment mold组合模
semi-positive mold半全压式模具
shaper定型模套
single cavity mold单腔模具
solid forging die整体锻模
split forging die拼合锻模
split mold双并式模具
sprueless mold无注道残料模具
squeezing die挤压模
stretch form die拉伸成形模
sweeping mold平刮铸模
swing die振动模具
three plates mold三片式模具
trimming die切边模
unit mold单元式模具
universal mold通用模具
unscrewing mold退扣式模具
yoke type die轭型模
mould for plastics塑料成形模具     
mould for thermoplastics热塑性塑料模     
mould for thermosets热固性塑料模     
compression mould压缩模   
transfer mould压注模、传递模      
injection mould注射模   
injection mould for thermoplastics热塑性塑料注射模    
injection mould for thermoses热固性塑料注射模      
成形零件
stationary mould fixed half定模      
movable mould moving half动模      
fixed clamp plate, top clamping plate. top plate定模座板      
moving clamp plate. bottom clamping plate. bottom plate动模座板      
upper clamping plate上模座板      
lower clamping plate下模座板      
cavity-retainer plate凹模固定板      
core-retainer plate型芯固定板      
punch-retainer plate凸模固定板     
chase. bolster. frame模套      
backing plate. supprr plate 支承板    
spacer parallel  垫块   
ejector housing. mould base leg支架
 
模具工程常用词汇英汉对照
die模具
figure file, chart file图档
cutting die, blanking die冲裁模
progressive die, follow (-on)die连续模
compound die复合模
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring弹簧
bolt螺栓
document folder文件夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count复盘点数量
quantity of customs count会计师盘,点数量
the first page第一联
filed by accounting department for reference会计部存查
end-user/using unit(department)使用单位
summary of year-end physical inventory bills年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部-(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card年终盘点卡与清册使用-状况明细表
blank and waste sheet NO.空白与作废单号
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
sample样品
incoming material to be inspected进货待验
description品名
steel/rolled steel钢材
material statistics sheet物料统计明细表
meeting minutes会议记录
meeting type会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办
PCE assembly production schedule sheetPCE组装厂生产排配表
model机锺
work order工令
revision版次
remark备注
production control confirmation生产确认
checked by初审
approved by核准
department部门
stock age analysis sheet库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked待验或重工
total合计
cause description原因说明
part number/ P/N料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
year-end physical inventory difference analysis sheet 年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
    • 电话咨询

    • 13610845997